简介:Themetal-organicchemicalvapordeposition(MOCVD)techniqueisapromisingprocessforhigh-temperaturesuperconductorYBa2Cu3O7-δ(YBCO)preparation.Inthistechnique,itisachallengetoobtainbariumprecursorswithhighvolatility.Inaddition,thepurity,evaporationcharacteristics,andthermostabilityofadoptedprecursorsinwholeprocesswilldecidethequalityandreproducibleresultsofYBCOfilm.Inthepresentreport,bis(2,2,6,6-tetramethyl-3,5-heptanedionato)barium(Ⅱ)(Ba(TMHD)2)wassynthesized,anditsstructurewasidentifiedbyFTIR,1HNMR,13CNMR,andESI-MSspectroscopy.Subsequently,thethermalpropertiesandthekineticsofdecompositionweresystematicallyinvestigatedbynonisothermalthermogravimetricanalysismethods.BasedontheaverageapparentactivationenergyevaluatedbytheOzawa,Kissinger,andFriedmanmethods,thevolatilizationprocesswasdiscussed,andallresultsshowthatBa(TMHD)2isunstableandhighlysensitivetothechangeoftemperatureduringthewholeevaporationprocess.Therefore,itisveryimportanttochoosesuitablevolatilizationtechnologyandconditionsforavoidingBa(TMHD)2break-down(orthermalaging)duringMOCVDprocess.Subsequently,thepossibleconversionfunctionisestimatedthroughtheCoats-Redfernmethodtocharacterizetheevaporationpatternsandfollowsaphaseboundaryreactionmechanismbythecontractingsurfaceequationwithaverageactivationenergyof118.7kJ.mol-1.
简介:本文针对N4/1Cr18Ni9Ti与N4/0Cr25Ni20复合板的特殊焊接要求,根据NB/T47014—2011《承压设备焊接工艺评定》的要求,制备2块N4/1Cr18Ni9Ti试板,2块N4I/0Cr25Ni20试板,尺寸均为500mmX150mmX(4+14)mm。不锈钢基层采用GTAW打底,焊丝选用HOCr21Ni10,SMAW填充与盖面,焊条选用A302与A402。镍复层的焊接采用手工钨极氩弧焊,焊丝选用含Ti、AI等脱氧元素的ERNi-1焊丝,保护气体选择98%Ar+2%H2。试板焊接完成,外观检验合格后进行100%RT,检测结果符合JB厂r4730,2—2005I级合格,镍复层进行100%PT,检测结果符合JB/T4730.5—2005I级。两种焊接试板分别取样并做拉伸、弯曲力学性能分析,镍复层焊缝做化学成分分析。通过两块焊接试板试验对比,不锈钢基层焊接材料选择HOCr21Ni10焊丝与A302焊条。镍复层焊接采用ERNi-1焊丝,焊接保护气体为98%Ar+2%H2。通过焊接工艺评定试验研究,解决了N4/1Cr18Ni9Ti与N4I/0Cr25Ni20复合板焊接问题,提高了用户坩埚的返修质量与再次使用寿命,为使用单位节约了成本。
简介:采用Gleeble热模拟方法研究Mg-6Zn-1Al-0.3Mn变形镁合金在温度为200-400°C,应变速率为0.01-7s-1条件下的热压缩变形行为。结果表明,变形温度和应变速率显著影响其热变形行为。通过计算获得了热变形激活能及应力指数分别为Q=166kJ/mol,n=5.99,且其本构方程为ε&=3.16×1013[sinh(0.010σ)]5.99exp[-1.66×105/(RT)]。热压缩显微组织观察表明:在应变速率为0.01-1s-1的条件下,在250°C热压缩变形时初始晶粒晶界及孪晶处发生了部分动态再结晶,而在高温(350-400°C)条件下,发生了完全动态再结晶且再结晶晶粒尺寸随着应变速率的增加而减小。获得的较优的变形条件为温度330-400°C、应变速率为0.01-0.03s-1以及350°C、应变速率为1s-1。